Tygogami In your second schematic the output of the OpAmp will be like the first waveform, but because of the resitor divider will be scaled and moved up so its minimum is about 0V and its maximum is about 5. Motorola products are not designed, intended, or authorized for use as datssheet in systems intended for surgical implant into the body, or other applications intended to support or sustain life, datasheeg for any other application in which the failure of the Motorola product could create lm datawheet situation where personal injury or death may occur. See how the signal is cut. This site uses cookies to deliver our services and to show you km ads and job listings. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable lm datasheet fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was lm datasheet regarding the design or lm datasheet of the part.

Author:Shajinn Digul
Country:Costa Rica
Language:English (Spanish)
Published (Last):3 April 2004
PDF File Size:15.86 Mb
ePub File Size:17.60 Mb
Price:Free* [*Free Regsitration Required]

They feature a factor of ten increase in speed over general purpose devices without sacrificing DC performance. The LM series has internal unity gain frequency compensation. This considerably simplifies its application since no external components are necessary for operation. However, unlike most internally compensated amplifiers, external frequency compensation may be added for optimum performance.

Overcompensation can be used with the amplifier for greater stability when maximum bandwidth is not needed. Further, a single capacitor can be added to reduce the 0. These devices are easy to apply and offer an order of magnitude better AC performance than industry standards such as the LM C temperature range.

The LM is specified from 0? C Lead Temperature Soldering, 10 sec. Small Outline Package Vapor Phase 60 sec. Infrared 15 sec. C ? C, the LM is ? C, and the LM is ? For operating at elevated temperatures, devices in the H08 package must be derated based on a thermal resistance of ?

The thermal resistance of the dual-in-line package is ? Note 3: The inputs are shunted with back-to-back diodes for overvoltage protection.

Therefore, excessive current will flow if a differential input voltage in excess of 1V is applied between the inputs unless some limiting resistance is used. C LM ,? C LM , and 0? C LM Also, power supplies must be bypassed with 0. F disc capacitors. The LM is in a unity-gain non-inverting configuration. VIN is stepped from? The slew rates between? Note 8: Human body model, 1. Fast Summing Amplifier Differential Amplifier www. Output zero. Full scale adjust. As used herein: 1. Life support devices or systems are devices or systems which, a are intended for surgical implant into the body, or b support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.

A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.

Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.

Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used.

Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices.

Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice.

TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications such as life support where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use.

Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI.

Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.






Related Articles